FWX645DBD1 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
it wouldnt drain and it was smoking
my husband took off all the parts and put the new ones on in about 45 min only to find that the motor was burned out and the motor is discontinued but all the other parts are available!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie L from Sledge, MS
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
We smelled rubber burning when I did laundry.
It was easy. No problem getting the to v-belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from minneapolis, AL
- Parts Used:
- 134511600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
she would not rattle and roll
I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Porter, ME
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
cold water continued to run and water leaked all over garage floor
The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheri from Wrightsville, PA
- Parts Used:
- 5303279394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
When filling the washer Water ran out of it and flooded the floor.
Remove the agitator and the 2 bolts that clamp the spin drum to the shaft and pull up on drum the 2 seals are on the shaft right there. Pry up on the seals to remove them. Install all seals and Be sure to completely clean all parts before putting them back in the machine and re assemble the machine. The bad part of this job is if you have used powdered soap it took 3 hours to clean the parts before reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Trinidad, CO
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burning smell from wash, needed new drive V belt
watched the video on website, printed instructions for feedback.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Randolph, ME
- Parts Used:
- 131862900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
bad rumble when running
released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecilia from Moreno Valley, CA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped spinning made noise
Changed the belt started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Austin, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy spin cycle
Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from Buyck, MN
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cold water would not shut off on washer
Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Portsmouth, VA
- Parts Used:
- 3204401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Agitator
Unplug unit. Unscrew securing nut, remove agitator, install new part (ensuring splines mate properly) and secure with nut. The nut is molded into the plastic top of the agitator, therefore no tools were required. Very simple and straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Millard from Grand Prairie, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Belt Had Smoked
Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.
Was this instruction helpful to you?
Thank you for voting!