FWS223RFS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from MEDFORD, OR
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Leaking drain pump
Replaced drain pump using this walk through. Different models, but pretty straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Unionville, PA
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
over fill caused door to come open
removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohamad from Chicago, IL
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer was not spinning
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ketchikan, AK
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would only let cold water in,then not fully cycle
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oxford, MA
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
water not coming into machine fast.
we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from DALLAS, GA
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
water filling in machine without turning on
I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mayfield, NY
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water over flowing, old valve stuck open.
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.
Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greer, SC
- Parts Used:
- 131461200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain Hose leaking.
Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Murrieta, CA
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
belt broke
Removed old belt. Installed new belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Saint Louis, MO
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Hot water was not entering the machine, but cold water flowed smoothly
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Asheville, NC
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer Not Draining
After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buford from LAWTON, OK
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump froze during subzero temp
Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbra from Mills River, NC
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Off/on knob broke
Pushed the new knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVEN from HAMPTON, GA
- Parts Used:
- 131461200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the drain hose was leaking
i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther
Was this instruction helpful to you?
Thank you for voting!