FWS645RBS5 Frigidaire Washer - Instructions

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.

Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.

Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.

replaced it with the new one

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

Checked drive belt by removing two screws on the BOTTOM of the front panel. Would spin dry but not agitate. Motor is two directional. Spin one way, agitate the other way. Same belt, so not the belt. Removed the agitator and the drive was turning but not the agitaor. It APPEARED that the agitator drive block was part of the agitator. IT IS NOT. Tap out the drive block,(Part # PSii52574)by threading a long bolt with the same threads as the screw that held the agitator to the drive assembly. Gently tap and the drive block will drop out. Replace the Agitator drive block. Worked like new for $21.32 + SH. The old agitator drive block was broken in pieces thus not allowing the agitator drive to turn the agitator back and forth. Did not need the Agitator, agitator screw or agitator spacer. Easy fix. No experience necessary. Cliff

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.