MWX223RED2 Frigidaire Washer - Instructions

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.

Unhooked old hose and replaced with new one.

The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightforward. And the washer no longer leaks!

This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.