FWS933FS1 Frigidaire Washer - Instructions

Had an electrician friend to do the removal and repair

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

It was easy. No problem getting the to v-belt.

I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.

removed two screw at the bottom of front panel and pulled down on panel to remove, determined water coming out splash seal, splash cover held on with plastic clips around cover. Removed two screws on back side of top and hinged top over removed splash cover and cleaned old seal out replaced with new seal.Simple job but could not find parts locally and found Partselect on internet and ordered parts, very friendly and knowledgible person, ordered parts and had them in three days, would very highly recommend. Thank You Joe Lumpkin

This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

removed front cover pushed in tensioner by hand walked belt off pulleys tilted belt removed lock ring pulled tensioner off noticed right rear lower tub brace broke at spot weods drilled out spot welds nut and bolted rear brace put springs back on base and installed belt works like new and saved myself from replacing lower washer tub frame so 70.00 and she up and running again

followed on line instructons very easy

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

replaced it with the new one

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.

Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.