LAFW7000LW0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eleanor from Jekyll Island, GA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would drain, but not spin
I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from TOLEDO, OH
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would go into high spin in regular wash settings .
(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lillian from PHILADELPHIA, PA
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass broken
By unscrew the washer Machine door off' then place the door flat surface and start to unscrewed each screw carefully keep all the screws together then remove the broken glass that you don't cut yourself in a safe place, then place the New glass back on & replaced all the screws back on tightly once all the screws back in then replaced it back on to the washer Machine, make sure you pre-test your washer Machine for no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernette from MIAMI, FL
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door wouldn't lock because the striker was broken
Unscrewed the old striker and screwed in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Baruch from HURLEYVILLE, NY
- Parts Used:
- 134618213
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
washer stops in middle of cycle and E53 appears on the screen
1 you have to order a new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Fruitland, ID
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not complete the spin cycle
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from hampton, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spin cycle sometimes
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from Santa Clara, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer drum would not spin
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manny from Old Bridge, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine wouldn't go into final spin.
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Saint Augustine, FL
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer drained withn no spin
Remove top of washer, remove door lock assembly,install new assembly replace top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from GUILFORD, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doesn’t close
Remove screws take off striker .Put striker back on with screws back on
Tighten screws. Took 5 minutes
Tighten screws. Took 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from ST MICHAELS, MD
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer door wouldn't lock so it would not run
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DELTONA, FL
- Parts Used:
- 134618213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
While using washer a E9F code appeared and stopped working.contacted parts select trouble shooting site they told me what it was ordered the part they were right on!back washing again thanks so much for the help!
Did it with no problems at all just followed the video step by step worked great done in 1hour!
Was this instruction helpful to you?
Thank you for voting!