FAFW4221LB0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JaNann R from Claremont, SD
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washed a pliers in the pocket of my pants, and shattered the inside glass of the door panel.
Simple removed the screws from the door, did this the night I broke the glass. Gently pryed the inside of the door apart from the front of the door panel. Lined up the arrows on the edge of the new glass panel with the inside of the front door panel and placed the inside plastic door panel back on, to hold the glass panel in place. Replaced screws. Everything worked great! Easy, affordable fix!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Sacramento, CA
- Parts Used:
- 131763256
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Part was very difficult to reach from the top.
There was not a video available on your site so I went to U-Tube and found one. Instead of reaching the part from the top I took off the rubber boot from the front and it was so much easier. Once I found and watched the video the entire repair took about 15 minutes. Now the washer works like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Wakefield, RI
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Went into pause mode when starting
Completed by my wife on line instruction video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Charlestown, MA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Error Code E43 - door lock problem - no spin
Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Dyersburg, TN
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not go into spin cycle
Took off top. Removed 2 screws on Door Lock Assembly and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SCOTT from SALINE, MI
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door lock mechanism broke and washer would not run
You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Bedminster, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Lock and switch didn't work
Using a youtube video, (which might have actually been related to parts select), the door lock replacement went smoothly AFTER I couldn't SEE the SPRING around the rubber boot, as the spring was the SAME color and with a little bit of dust on it, was indistinguishable. As soon as I found it, the rest was fairly simple. I MIGHT even try replacing the moldy boot on these stupid front loaders...I paid for overnight shipping as I also had Geek squad guys on hold for repair, and needed to know fast, whether or not this would do the trick. HOORAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Centuria, WI
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door would not latch and washer failed to start
Remove the 2 screws on the rear of the top panel. Open door and remove the 2 screws holding the latch assembly. Reach down and pull up latch. Remove the 3 wire connectors. Plug wire into new latch and re-install in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Tampa, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Door would not lock shut
Everything went great, except replacing the rubber seal, that was a little bit harder to put back in place. But other then that, went very well and easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ricardo from nesa, AZ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken doorlatch
Remove the top cover and the doorlacth and unplug the old parts as simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darci from Norwalk, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doors tricker broke
The repair was so easy!!! It took me less than ten minutes to remove the broken piece and to install the new piece. There were 2 screws to remove to get the broken piece off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Opelika, AL
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
A part of the door lock assembly was broken, causing the washing machine not to start.
The entire process, from diagnosing the problem, ordering the part, and instalation was fantastic! I ordered the part Friday afternoon and had it at my door Saturday afternoon. I was so relieved to read the installation posts from other customers demonstrating how common this issue is and how easy it was to fix! I simply watched the installation video that was sent with my confirmation email. It is also conveniently located on your website. I had the new part installed in less than 30 minutes AND before my husband got home! Thank you Partselect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from egg harbor twp, NJ
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door striker
first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Doe Run, MO
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer would not go in high spin
It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Simpsonville, SC
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would not start after I opened and closed the door.
Removed the door lock and switch assembly. With needle nose pliers, I removed the metal ring around the washer gasket. Removed two screws on assembly and removed the entire assembly. Noted part number and ordered part which came in 3 days. Reversed the above instuctions for removing the assembly. Was washing within the hour. By the way, I am a 65 year old woman.
Was this instruction helpful to you?
Thank you for voting!