FAFW3511KW1 Frigidaire Washer - Instructions

Followed the video instructions to the letter. so easy. Door works great and will certainly come back if and when I need any parts.

Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.

For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!

"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

The video was most helpful, and the left shock replacement went as shown. The sucker punch was getting to the right shock - much harder.
First notice video has washer on a stand. How nice to have had it up on a table. LOL As it was I tilted the machine back with a 6 inch block under the front. Still a bear to get to the shock, but w/ patience, doable even though you are flat out on the floor.
The old shocks were so bad that the pistons fell out once it was removed.
It takes some strength to get the pins through the new shocks, and as I have a weak left hand I had to resort to using a C-clamp to help. If I could have gotten my right hand in there I may not have needed it. Right hand did have to hold the clamp as it had to just catch the side of the pin hole since the pin is pointed and sticks out past the mounting bracket when seated.
I also ordered a spring but they both were still good.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.

replaced the two shocks with the new ones by removing the pins that held the old ones in place.

Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

My shocks on the washer were broken, in part because of age, the other is broken spider drum inside the barrel. Was very easy to do the shocks. Unhook water connections and power. Move washer away from the wall. Remove the back cover from the washer. On the left side, you have to remove two screws from the electronics control box so you can gently move it out of the way. Then grab the plastic pin with some pliers and pull while depressing the locking lug on the end of the pin (Very important to depress the lock or you will have to buy new pins) Remove both pins for each shock. I used some high pressure grease on the pins when I put it all back together. Was a quick fix. Unfortunately had to take it all back apart as this was only a small part of my issue with having the stainless drum being broken inside.

Remove screws take off striker .Put striker back on with screws back on

Tighten screws. Took 5 minutes

Remove top of washer, remove door lock assembly,install new assembly replace top.