FAFS4473LA0 Frigidaire Washer - Instructions

Our washer is in a very tight spot, and we use the top for storage, so it was a job moving everything and pulling the washer away from the wall. Unplugged, then took the 2 screws off the back, dropped one and retreived it with masking tape on a dowel. Got the top to slide back, then took the screws off the latch. Crammed my arm down inside (very tight) and grabbed the latch, pulling it out the top. Labeled both sides of the connections with colored masking tape (in case we need to replace this part again, but I hope not). Got everything back together, then put the top back on, dropping the same scew behind, retreived it,plugged the power in and it works!!

with a code it gave me i was able to determeine it was the door lock switch it was so easy it was unbelievable

First I watched a youtube video on how to do it. Then I took to machine apart and was able to replace the boot in a short period of time. You have to be careful when putting it on so the guides in the rubber line up with the pipes. It is a good idea to check the filter every few years because it does collect lint and strings that will clog the drain and cause the machine to leak or drain slowly.

It took all of five minutes, two screws and done. Saved $150.00 on the service charge, while the part cost less than $15.00 for the parts including S/H.

Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.

I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks

very easy, just put in the 2 screws and it was fixed..

Took off top. Removed 2 screws on Door Lock Assembly and replaced.

You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!

Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.

Removed two screws, installed new piece.

Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!