ATF6700FS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Viola, DE
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Tub was rocking a lot on spin
The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from DEFIANCE, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The water would not completely drain and go to spin cycle and noisy while trying to drain.
I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from THOMPSONVILLE, MI
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer woild not spin out left clothes sopping wet
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from IOWA PARK, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Impellar was broken on the washer drain pump.
Removed front panel and unplugged wire connector to drain pump. Loosened two hose clamps and removed hoses the unbolted drain pump from washer frame. Simple removal and even simplier installation of new drain pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blake from WINTER HAVEN, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken shock
Watched the video on website and followed what they said. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theresa from W SACRAMENTO, CA
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
off balance and walking
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from INDIANAPOLIS, IN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The small plastic piece broke that locked the door.
Screwed the new part back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from hampton, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spin cycle sometimes
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from LOVINGTON, NM
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Catch on door strike broke.
Removed and replaced two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from ST MICHAELS, MD
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer door wouldn't lock so it would not run
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from LONE TREE, CO
- Parts Used:
- 134371220
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer was filling with water when not in use
This repair was pretty simple. Unplug washer from electrical outlet and remove hoses. This is a good time to replace the hoses. Removed two screws at the back of the washer to remove the top of the washer. This exposed the faulty valve assembly. Disconnect the three connections. There are two screws holding this part in place. The top one is easy to remove, the bottom one is a little more difficult due to access. Remove plastic retainer plate on back of washer. Remove faulty valve assembly. There are two rubber grommets/gaskets that will need to be removed from the faulty part and installed on the new part. Slide new assembly into place. Secure with the two screws. Replace retainer plate. Reattach power connections. Reattach hoses and finally Reinstall top of washer. Total time was right around 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LINCOLN, ME
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece of door latch lodged in switch
Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W R from Venice, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
worn out vibration/shock absorbers
"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Saint Augustine, FL
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
Was this instruction helpful to you?
Thank you for voting!