FTF2140FS1 Frigidaire Washer - Instructions

Simply removed several screws around inner glass Then part set right into place. replaced all the screws and was completed.

Removed the old screws and old hinge. Put on the new hinge with new screws. Tightened 'em up and we were good to go. Pretty boring and basic. But beats the hell of not having the washer door close!

Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

Totally unable to move old vane using instructions on this site. Wound up breaking old unit in pieces to remove. Installed very easily. However when trying to install enclosed screw (which you are supposed to install through vane into tub) it did not line up even close to hole drilled into tub. I had wondered why the original vane didn't have a screw in it, now I know.

I removed the two screws holding the old handle on and then then installed the new handle

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, put the hoses on, plug in motor and replace front panel. plug into wall

The washer door wouldn't shut. I saw the top piece of the plastic catch appeared to have a broken section. I looked online at the replacement part needed (this was the most difficult part of the process). I unscrewed the old piece and replaced it. No problems. I suspect that this is an engineered flaw with the machine to encourage more unit sales (it could be metal for instance). So fix it and feel clean!

I have a stackable unit. My son and I removed the dryer from the top of the washer, removed the top, and rear panels on the washer. We romoved the old water valve, and installed the new one. It was a VERY simple repair.

First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no handy man so thats how easty it was.

Ran diagnostic and discovered that the panel did not recognize that the door was locked, thus no spin. I ordered both parts, although I didn't need the door strike/catch. I only needed the locking mechanism. I removed metal ring from around the rubber piece inside the door with needle nose pliers, and then I simply plugged in the new lock and screwed it in place. I put the ring back around the rubber piece, flipped the circuit back on and washed a load of clothes. Easy as pie! Teachers can do anything. Who needs a repair man? :)

Once I figured out that the shocks were broken it was very easy to fix. Remove back panel first. Then remove the control box on bottom left corner to gain access to the left shock. Pinch the locking mechanism on the plastic locker bolts and remove the four bolts from both shocks. Replace with new shocks and replace control box and back panel. It probably took more time moving the washer to where I could work on it then it did to fix it. Works like new.

Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new board. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.

The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

Unscrewed two screws, replaced door striker and screwed the same two screws back in! I was done in less than 3 minutes!

I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.