FWS833AS3 Frigidaire Washer - Instructions

Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working like a champ now. $20 total with shipping. Not too bad to save a washing machine.

I push the new knob onto the post that fit the knob

Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.

I just removed the broken foot with a pair of plyers and screwed the new one on. The decorative side panel popped right into place.

Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

Replaced drain pump using this walk through. Different models, but pretty straight forward.

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

Pushed the new knob into place.

Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done

Removed old belt. Installed new belt.

I had to remove agitator and clean under it.