GLWS1233AS1 Frigidaire Washer - Instructions

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

I had to remove agitator and clean under it.

Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

This repair took only about 15 seconds to complete. It just involved pushing the new knob on the selector. The provided video should give you the confidence to complete this task.. I invested $11.00 for the part. I would hate to see the cost to have a repairman come and fix this. Worth every penny

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

old knob was broken so didn't stay on and work so had to use pleris to adjust temperatures when needed but now just put new knob on and we are in buisness and like new again!!! So glad I found your company and had the knob i needed and fast service!! thanks :)

Removed old belt. Installed new belt.

Let me start by saying, I ordered these 2 knobs for my dryer and they came faster than lightning. I was so glad to know that I could order something and have it within 48hours. KUDOS! Onto the actual item, I got the 2 knobs and since it was just the knobs that broke off and not the mechanism itself, I just took the knobs out of the package and put them on the mechanism by pushing on and VIOLA! , I was done!
If I ever need anymore parts for any of my other appliances I will sure use Parts Select and I will sure tell my friends about you guys too!!
Good Prices.. Fast Shipping.. gotta love it!

I pulled off the broken knob's metal shaft that remained attached to the operating spindle and slid the knob onto the machine.

Took it out of package..pushed it on.

Just push the new knobs on slot. Very simple process. The best part is that it was relatively cheap and the shippping to my home was fast. Thanks.

just slid the new knob and that was it.I have say about PartSelect.com , it was very easy to place order and next day i rec'd the part. excellent service.

This is a case of not knowing the proper tool to do the job. I went to turn on the machine and the knob broke( common on this machine). The stub of the knob fell into the machine. Thought that the access plate was put on with screws. I saw that the hole was similar to an allen hole. I couldn't get the screws out so called a repairman. He spent 10 minutes, charged me $65 and then told me that most newer appliances need a tool called a robertsons screw driver to get the screws out without stripping them. I felt like a dope, a $4 tool could have saved me $59. A word to the wise, learn what tools do the job and this won't happen to you. JT