GSWS9719AS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from EL PASO, TX
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob replacement...
watched you tube video... a breeze
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Flemington, WV
- Parts Used:
- 134418700
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
transmission wore out
After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from TEMPLE, GA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken belt
Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WOLVERINE, MI
- Parts Used:
- 134511600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Smell of rubber under dryer. Inspection proved belt cracked and shinny worn spot.
Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sault Ste. Marie, MI
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drive belt old and stretched
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph W from WEST PALM BCH, FL
- Parts Used:
- 134548800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leveling leg sheared off
Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from STATEN ISLAND, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The water did not drain at all . You could hear the pump spinning , but it was not .
After making sure there was no blockages and the pump was not jammed I knew it was time for a new one . Unplug the machine and turn off the hot and cold water . Remove the two screws on the bottom of the front of the machine and push down on the panel it should come right off . Make sure all the water is drained out of the tub use a wet/dry vacuum to suck out all the water if needed . Then with the vacuum empty squeeze the clamps that hold the hoses on the pump and push them out of the way . Use the vacuum to suck up any leftover water, as you remove both hoses . Unplug the one set of wires going to the pump . Remove both screws and the pump should now be loose . Do the same thing in reverse to install the new pump . Other than dealing with the water it should take under 15 minutes . Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from WEST POINT, GA
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Agitation weak
Got the washer used. Agitation was okay, but the screw part of the agitator was very weak and kept slipping, so bought a replacement agitator. This DID NOT fix the problem, it remained the same. Watched a video on this site about the part under the agitator, whereupon we saw there was supposed to be a washer on top of the spike-thing where you screw the agitator down. THAT was the problem. That washer was missing, and when we replaced it, the agitation was fixed! Very much appreciate this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Beverly Hills, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced knob, perfect fit and match
just pushed new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENISE K from cleveland, OH
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old knob was strip
remove old knob and washer that was on it put new knob on and turn the knob dryer was save
Was this instruction helpful to you?
Thank you for voting!
Bottom "Screw", which is the front leg of the washer was broken.
Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Alpena, MI
- Parts Used:
- 131624500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing cup for fabric softener
Pulled it off and just replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melissa from west chicago, IL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
plastic start knob stem broke off
First I unscrewed the back panel to be able to lift the cover off the control panel. I then removed the cover off the control panel and slid the knob into the locking tabs. I replaced the cover and screwed the back panel back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohamad from Chicago, IL
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer was not spinning
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Thornton, CO
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burning rubber smell
Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo
Was this instruction helpful to you?
Thank you for voting!