GSTF7200DS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- theresa from W SACRAMENTO, CA
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
off balance and walking
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Fruitland, ID
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not complete the spin cycle
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from PHOENIX, AZ
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Latch broken. New part installed as per repair video - no problems.
New part installed as per repair video - no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ROY, UT
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken plastic door strike
Easy fix for a verry poor designed door catch. Almost purposeful on the manafactures behalf to make it out of cheap plastic Remove 2 screws replace install 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Viola, DE
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Tub was rocking a lot on spin
The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Milton, VT
- Parts Used:
- 137108000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bearings in pump were lose and the washer was not pumping the water out
First I pulled the front panel on the washer off, than I unplugged the wires to the pump, took the two screws out that hold the pump, took the two hose clamps off and took it out. To replace I did the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from INDIANAPOLIS, IN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The small plastic piece broke that locked the door.
Screwed the new part back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from hampton, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spin cycle sometimes
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from sterling hgts, MI
- Parts Used:
- 137108000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
pump not working
took off 2 screws and 2 hose clamps put in new part. Put srews and clamp back on less than ten minutes. total cost with shipping $62.00. repair person wanted $265.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from VANDALIA, IL
- Parts Used:
- 137108000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drain pump was out
Repair was easy watched video it was spot on I went to auto parts store and bought 2 screw clamps to replace the spring clamps and made repairs easier washer works great happy wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from ST MICHAELS, MD
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer door wouldn't lock so it would not run
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from LOVINGTON, NM
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Catch on door strike broke.
Removed and replaced two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Amherst, WI
- Parts Used:
- 137108000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Wouldn't drain water...thus no spin cycle!
Let's see...removed lower panel-used tools to unscrew the unit---one piece-nice to replace---EASY to replace! Removed hose---placed hose on new unit; screwed all back to bottom of washer-replaced lower panel...Voila! Made sure unit was balanced...did a load of whites---Awesome WASHER NOW!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W R from Venice, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
worn out vibration/shock absorbers
"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.
Was this instruction helpful to you?
Thank you for voting!