The door striker is a part found on the door of your washer, and it activates the door switch which signals that the door is closed. This genuine OEM replacement part is also known as a door latch or ...
This door lock and switch assembly is an authentic OEM replacement part for your front load washing machine. The lock is used to prevent the door from opening while the machine is running, and the swi...
The shock absorber kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin, and 4 locking nuts. These shock absorbers keep the washer from vigorous sha...
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
This screw-in plastic leveling leg supports the washing machine. If your washer loses balance while it is tumbling, or makes loud noises, then it is best to replace the leveling leg to make sure the h...
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
This washer door boot spring clamp secures the rubber door seal in place, maintaining a tight, watertight fit between the tub and front panel during operation. Its tension design helps prevent leaks a...
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
In Stock
Order now and your part arrives by Jul 5
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kara Copeland
May 9, 2026
FRONT LOAD FRIGIDAIRE GALLERY SERIES WASHING MACHINE HAS A WET, DANK SMELL AFTER RUNNING WASHER. I WIPE DOWN DOOR AND DOOR GASKET AND REMOVE AND DRAIN WATER IN SOAP DRAWER, AFTER EACH WASH. DOES THIS MACHINE HAVE A COIN CATCHER? THOUGHTS?
For model number GLTF2940FS1
Hi Kara, thank you for the question. Yes, your washer has a coin trap, more technically known as a pump filter. A clogged filter is a very common cause of persistent odors because it traps stagnant water, lint, and debris. It is located inside the drain hose. You may need to rinse the filter in the sink and reach into the pump housing to clear any hair or gunk. We hope this solves your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. The
... Read moren along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
