MWX233RES2 Frigidaire Washer - Instructions

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

Removed old pump and installed new pump in same order. Only problem was reinstalling wire spring clamps with hoses on new pump. Not enough room to use pliers to open clamp. Otherwise a simple installation. A small vise grip pliers might help to hold clamp open. Check and rotate inlet/outlet end of pump as included directions describe first before installation.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.

I had replaced the pump 5 years earlier and now it was leaking again. When I removed the old pump, I discovered a bobby pin had made its way into the pump and was chewing up the housing, causing a small hole. This was a very simple repair as the pump sits right in the bottom front of the machine. The most difficult part was removing the old hoses and re-attaching them to the new pump. Four bolts/screws and two electrical connectors, which cannot be confused, made this an easy fix.

part was fast easy to put on know work better then before

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

Removed old belt. Installed new belt.

At first I thought the o-ring may have wear out so I took the pump out to check, but the leak was either from the shaft seal or body itself (hard to tell as body had corrosion on it) taken out the pump was very easy, but you need to use the right pliers to easily remove the spring clamps. Follow instruction to set the housing orientation, and than install back the pump. Reinstalling one of he hoses using the spring clamps took few tries, but it was in place in no time. remember not to install the cover before you operate the washer to verify no leaks. This work is realy very very easy.

Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

took of the front cover. then i took off the plastic cover on top of the water pump. then i unbolted the water pump and disconnected the hoses. i had to rotate the water pump connections. i swap the base of the pump and then bolted it back in place connected the water hoses back and then put the plastic cover back on. and to finish i put the front cover back and i was done.