LA560AXW1 Frigidaire Washer - Instructions

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!

The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the control panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

Remove the agitator and the 2 bolts that clamp the spin drum to the shaft and pull up on drum the 2 seals are on the shaft right there. Pry up on the seals to remove them. Install all seals and Be sure to completely clean all parts before putting them back in the machine and re assemble the machine. The bad part of this job is if you have used powdered soap it took 3 hours to clean the parts before reassembly.

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.

followed on line instructons very easy

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.

Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.

Changed the belt started working like new.