FWS645GFT1 Frigidaire Washer - Instructions

i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

part was fast easy to put on know work better then before

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.

At first I thought the o-ring may have wear out so I took the pump out to check, but the leak was either from the shaft seal or body itself (hard to tell as body had corrosion on it) taken out the pump was very easy, but you need to use the right pliers to easily remove the spring clamps. Follow instruction to set the housing orientation, and than install back the pump. Reinstalling one of he hoses using the spring clamps took few tries, but it was in place in no time. remember not to install the cover before you operate the washer to verify no leaks. This work is realy very very easy.

Fairly easy repair to replace the discharge pump assembly. Remove the access door, pump shield, disconnected the hoses, remove the hoses, and the pump housing screws. Orientation of the water pump had to be changed to match original, easily done by rotating the pump hosing. Installed in reverse order and job was complete

I had replaced the pump 5 years earlier and now it was leaking again. When I removed the old pump, I discovered a bobby pin had made its way into the pump and was chewing up the housing, causing a small hole. This was a very simple repair as the pump sits right in the bottom front of the machine. The most difficult part was removing the old hoses and re-attaching them to the new pump. Four bolts/screws and two electrical connectors, which cannot be confused, made this an easy fix.

Removed old belt. Installed new belt.

I had to remove agitator and clean under it.

Replacing the pump assembly only involved:
1. Unplugging the washing machine!
2. Removing 2 screws to take off the washing machine's lower front panel.
3. Removing 2 bolts to take off the cover over the remote pump assembly.
4. Changing out the pumps required:
A. Unscrewing the 2 screws that secure the assembly harness to the washing machine's base.
B. Unclasping the 2 tubes using curved jaw pliers.
C. Disconnecting the electrical connectors by hand.
D. Removing 2 bolts from the assembly harness and the pump assembly.
5. Reverse steps 1 - 4 to install the new pump.

This is the third time it has been replaced. They last about 2-3 years. Made sure pump was full of water before starting etc so we didn't start with a "dry" pump.

The actual repair and parts ordering went just fine.

Scotty

disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Remove old pump, only a scrwedriver needed.
Save myself @ $100