MWS833AS1 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Clatskanie, OR
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad belt
did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karrie from Boulder, WY
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
worn belt
Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Burlingame, KS
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer was leaking
I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecilia from Moreno Valley, CA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped spinning made noise
Changed the belt started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmo from Apache Junction, AZ
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
I was only getting hot water
I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Oquossoc, ME
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
A Leak In The Water Inlet Valve
It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lutz, FL
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Replace water inlet valve.
Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie L from Sledge, MS
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
We smelled rubber burning when I did laundry.
It was easy. No problem getting the to v-belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from minneapolis, AL
- Parts Used:
- 134511600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
she would not rattle and roll
I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Porter, ME
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
cold water continued to run and water leaked all over garage floor
The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!
Was this instruction helpful to you?
Thank you for voting!