MTWX23VRGS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from minneapolis, AL
- Parts Used:
- 134511600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
she would not rattle and roll
I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie L from Sledge, MS
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
We smelled rubber burning when I did laundry.
It was easy. No problem getting the to v-belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Austin, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy spin cycle
Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Clatskanie, OR
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad belt
did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Calexico, CA
- Parts Used:
- 134418700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Portsmouth, VA
- Parts Used:
- 3204401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Agitator
Unplug unit. Unscrew securing nut, remove agitator, install new part (ensuring splines mate properly) and secure with nut. The nut is molded into the plastic top of the agitator, therefore no tools were required. Very simple and straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Daingerfield, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hose leaking
lifed the lid .remove oud hose and replaced with new hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Mohrsville, PA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
20 year old v belt finally gave up the ship
This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Millard from Grand Prairie, TX
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Belt Had Smoked
Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karrie from Boulder, WY
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
worn belt
Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Landing, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old belt
Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Jacksonville, FL
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer leaks when spin drying
Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.
Was this instruction helpful to you?
Thank you for voting!