FWS933FS2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbra from Mills River, NC
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Off/on knob broke
Pushed the new knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buford from LAWTON, OK
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump froze during subzero temp
Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Newport Beach, CA
- Parts Used:
- 131758600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer would not advance on cycles
Had an electrician friend to do the removal and repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANNA from STATEN ISLAND, NY
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherry from ellenburg depot, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from wilmington, IL
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would flood out the floor now and then
One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William F. from Poughkeepsie, NY
- Parts Used:
- 134592700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain hose was leaking
on front of machine,,,removed 2 screws at bottom corners. open top cover, using putty knife to release spring clips between front panel & top cover, lift & support top cover.note; tape hinged lid of machine to hold closed.the remove front panel of washer using a downward motion.re move spring clamp on water pump ,w/pliers, by sliding clamp upwards along drain hose. with a twisting motion,remove hose from pump.thread old hose out through back of machine.reverse reassembly,using new drain hose.note; suggest using an automotive radiator hose clamp on pump/hose connection instead of spring clamp.most spring type clamps will lose their tension with repeated plier action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Deshler, NE
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tenant lost knob and landlord replaced it.
Just pushed the knob on to the metal on-off control,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Cutchogue, NY
- Parts Used:
- 131758600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wash timer would not advance
My guy got a beer and followed the advice from John from Covino CA. Thank you John, the part about pulling the pen sure made my guys repair a piece of cake! He replaced the timer and put the panel back on and I was doing a load of laundry immediately. My advice is follow John's advice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Calexico, CA
- Parts Used:
- 134418700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Magnolia, MS
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Excess noise in pump, forigien drill bit hitting inpeller blades
Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Daingerfield, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hose leaking
lifed the lid .remove oud hose and replaced with new hose
Was this instruction helpful to you?
Thank you for voting!