LTF6000FS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from IOWA PARK, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Impellar was broken on the washer drain pump.
Removed front panel and unplugged wire connector to drain pump. Loosened two hose clamps and removed hoses the unbolted drain pump from washer frame. Simple removal and even simplier installation of new drain pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from INDIANAPOLIS, IN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The small plastic piece broke that locked the door.
Screwed the new part back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glenn from hampton, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spin cycle sometimes
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theresa from W SACRAMENTO, CA
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
off balance and walking
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blake from WINTER HAVEN, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken shock
Watched the video on website and followed what they said. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LINCOLN, ME
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece of door latch lodged in switch
Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from BOTHELL, WA
- Parts Used:
- 134550500
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door sagging, plastic broken
Followed the video instructions to the letter. so easy. Door works great and will certainly come back if and when I need any parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manny from Old Bridge, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine wouldn't go into final spin.
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Saint Augustine, FL
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W R from Venice, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
worn out vibration/shock absorbers
"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from Santa Clara, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer drum would not spin
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer drained withn no spin
Remove top of washer, remove door lock assembly,install new assembly replace top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy L from Twin Lake, MI
- Parts Used:
- 134371220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the part cracked from water freezing
First I removed the two screws that hold the part in place. I then pulled the part out about 3 inches and disconnected the three wires from the part and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Cambridge, NY
- Parts Used:
- 5304485917
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
shocks broke away from washer drum
replaced the two shocks with the new ones by removing the pins that held the old ones in place.
Was this instruction helpful to you?
Thank you for voting!