LTF6000FS0 Frigidaire Washer - Instructions

Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.

Remove 3 screws to remove door and remove all screws on back of door and had to pry up on the cover - new hinge assy set in ok and reasemble was easy but new hinge assy didn’t quite match mounting holes so a bit difficult to line back up

First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS

Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!

Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
Part arrived 2 days later, took about 40 minutes to install.

2 screws and about 48 seconds of work. very easy.

door not level son slammed shut and door strike broke

No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board

Replaced the hinge. Took old one off, put new one on.
I did not need to use new screws so I have returned them for a refund. Old ones were just fine.
Customer service was excellent, providing a return label, letter and simple instructions for the refund. Waiting for it to credit on my account.

E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door lock in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids

Followed the youtube video step by step. Very helpful video. Be careful of hinge screws. They are very easy to strip. Had to buy a special tool to remove stripped screws. Advice go ahead and purchase the 4 screws. 3 for the hinge and 1 for spare. Rest of the repair was easy. Less than an hour to complete.

First, I recommend you have a second pair of hands. The chrome door is quite heavy. Using Phillips screwdriver I removed the screws that attached the door to the frame. I had a helper hold the door while I removed the screws.
Once hinge screws were removed I put a towel down on a counter to keep the front of the door from getting marked up and proceeded to remove all of the screws around the back of the door so that I could lift the frame up enough to remove the broken hinge and insert the new hinge. It was a bit tricky to get the new hinge with bushings in place. I gently lifted the frame up with a flat head screw driver to widen the opening so I could get the bushings on the new hinge into position on the frame. Make sure they are properly inserted before you start tightening up screws.
Next, replaced all the screws on the frame, returned to the washing machine with helper who held the door up while I aligned the holes in the new hinge to the holes in the frame around the opening to the washer.
After everything was secured and tightened, to my surprise, the door latch did NOT line up with catch without lifting up about a 1/4" or a little more, on the bottom of the door. If someone slams the door without doing that you could break off part of the plastic latch or damage the catch inside the door frame.
I believe the original holes on the door frame were not drilled precisely during the manufacturing process and that is why the bottom bushing broke. We have always had to lift up a bit on the door to line up the latch with the catch. Eventually the strain on the bottom bushing caused it to break and then the door tilted down so you had to lift it up about 3/4 inch to latch it. I bought new hinge because if the top bushing broke the door could have come off.
Next time I buy a washing machine, I will pay more attention to the line up of the door latch with the door catch.
Flashlight helped me line up the holes.

I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.