LA700AXW3 Frigidaire Washer - Instructions

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.

Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.

Changed the belt started working like new.

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

I used this website to look at the parts breakdown the only way water can get into the machine is thru the solenoid valve. Ordered valve.Followed the video on how to replace valve.I pulled apart the old valve. The plastic seat was cracked,letting water seep into the machine.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

watched the video on website, printed instructions for feedback.

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.