PTF7012MW1 Electrolux Washer - Instructions

Nothing to it rteall. The great thing was how fast this company got the part to me!

I was amazed at how quickly my part came for the washer and it came to me on a Saturday

ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!

unscrewed the 2screws from the striker on the washer door first. Then put screwed new striker on door with its new screws. It was a piece of cake.

Unscrew the the bad part, screw on the new part

Washer error code said control board($200.) but this web site said Door Lock and Switch assembly($80). Web site was correct, thankyou for saving me money and time for the real repair needed.

with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.

as on the video. so easy. took longer to clean-up

There was not a video available on your site so I went to U-Tube and found one. Instead of reaching the part from the top I took off the rubber boot from the front and it was so much easier. Once I found and watched the video the entire repair took about 15 minutes. Now the washer works like new!!

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.

The door assembly did not fix the problem this time, it was the control panel that had to be replaced. I have replaced the door assembly in the past, and I am glad I have a spare on hand. They do go out over time from the pressure of large batches of clothes. I am "no repair man", but having someone come out to replace it for you is a $300.00 job, easily. Read the tech info for your error code and go from there.

Remove top. (2 screws). Remove Plastic cover plate from back where hot cold connections are made (pry carefully to release tabs). Remove vent tube by turning and pulling out.(this allows easier access to second screw). Remove all three color coded electrical connections. Remove two screws that retain valve (this is where I recommend a magnetic bit. (don't drop either screw) Pull valve out, then up and back in to remove. Reverse to install. Good Luck.

Everything went great, except replacing the rubber seal, that was a little bit harder to put back in place. But other then that, went very well and easy to repair.

Our washer is in a very tight spot, and we use the top for storage, so it was a job moving everything and pulling the washer away from the wall. Unplugged, then took the 2 screws off the back, dropped one and retreived it with masking tape on a dowel. Got the top to slide back, then took the screws off the latch. Crammed my arm down inside (very tight) and grabbed the latch, pulling it out the top. Labeled both sides of the connections with colored masking tape (in case we need to replace this part again, but I hope not). Got everything back together, then put the top back on, dropping the same scew behind, retreived it,plugged the power in and it works!!