CW8413W2 (PCW8413W2 A) Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephanie from Lawrence, KS
- Parts Used:
- WP34963
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water pumped in very slowly.
Unplugged washer, turned water valves off, disconnected water lines from washer with adjustable channel-lock wrench. Water inlet valve was mounted on its own plate that needed removed using a screw driver. Disconnected the electric sensors and disconnected the outlet hose. Valve had to be taken off the mounting plate with a nutdriver. Replaced valve and reconnected everything. Water pumped in 10 times faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from O'Fallon, MO
- Parts Used:
- WP34963
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No Hot water
I purchsaed a new water valve and it was very easy to install. I hate to do thos kind of repair but it went very smooth. Took maybe a half hour, and now it works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Klamath Falls, OR
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
drain hose had a hole near wall drain.
The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.
Was this instruction helpful to you?
Thank you for voting!
Leaking water
detached 2 inlet/ oulet hose/ hose clamps.removed the 4 motor/ pump base screws, tilted motor/ pump assembly and pulled from washer. Removed the 3 pump housing screws, removed pump/ old drive belt. installed new drive belt, pump, reattached pump screws, motor/ pump base screws, reattached hose/ hose clamp. Rreplacement of parts took approxmiatley 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Farmington, UT
- Parts Used:
- 31239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Two of the three wash cycles were not running properly
Diagnosing and ensuring that this was the problem took much longer than the actual repair. This was a simple repair, removal of six screws to access the timer assembly, two small bolts hold the assembly in place. Very easy to access and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chatwin from Houston, TX
- Parts Used:
- 31239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
intermittently halts mid-cycle
remove six screws: three along top of the control panel, three along front bottom of control panel. Pull control panel loose. Unscrew the timer knob by twisting it counter-clockwise. Remove the timer, unplug the timer quick-connect, replace timer and reinstall timer and control panel by reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Plumas Lake, CA
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
pump leakage
You tubed this procedure and it took 20 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- millie from hot springs village, AR
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
pump leaking water
remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Oreland, PA
- Parts Used:
- WP28808
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
fan belt was broken
First thing I did was to read the great information from other customers. John from Milton's post titled "frayed v belt" was excellent; so was Joseph from Goldsboro NC under the Pump part posts. I would add the following info which wasn't readily available. The Torx/starbit size mentioned in the posts referenced is a T25 the Amana lw8203w2 I have. I bought a t25 size torx wrench at my local hardware store for $2. I got everything together --the belt took some arm strength for an amateur like me to get on. Also, would recommend gloves as some of the edges are sharp down there. Everything appeared okay and when I started the spin cycle it started then cut off. I thought maybe besides the fan belt there was electronics faulty. However, I found an amana repair guide for my model online at scribd and under the troubleshooting section, it described the cutout of the spin cycle and if the new fan belt is too tight, it will bind and the spin cycle will cut out. So I opened up the front again and worked the belt for several turns to "stretch it" and voila, it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Cornville, AZ
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
pump seal leaking
After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.
Was this instruction helpful to you?
Thank you for voting!