CW20T6A Crosley Washer - Instructions

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!

First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.

Hardest part was figuring out how to get to the water valve. Turned out that the way in was from the top. All I had to do is remove two screws at the back of the top panel, and then unclip the front edge of the top panel (use a thin screwdriver to press in on the clips from the front of the machine). From there, it was easy to reach down inside and remove/replace the valve.

It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was stiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00

Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.

Followed the great instructions on your video

raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.

I changed the piece easily

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.

pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!