CW9203W2 (PCW9203W2 B) Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Washington, PA
- Parts Used:
- 205217P
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The pump housing had a large crack in it
The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- millie from hot springs village, AR
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
pump leaking water
remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Plumas Lake, CA
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
pump leakage
You tubed this procedure and it took 20 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Cornville, AZ
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
pump seal leaking
After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.
Was this instruction helpful to you?
Thank you for voting!
Washer "making a high pitched sound" and a burning rubber smell
As described by your information. Also watched your videos about repair. Your web site is amazing and we WILL use it in the future. We have a perfectly running washing machine once again. Thank You!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Martinsville, VA
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
wwater pump was leaking
My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.
Was this instruction helpful to you?
Thank you for voting!