CAW12444XW2 Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Carteret, NJ
- Parts Used:
- W10440729
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
when in spin mode machine walks around the cellar
Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from ACUSHNET, MA
- Parts Used:
- W11385424
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No agitation
Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ace from VENICE, FL
- Parts Used:
- W10205824
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The spin cycle was very noisy & shook the whole machine.
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
By the way, it didn’t solve the problem.
Paul
By the way, it didn’t solve the problem.
Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from MOUNTAINBURG, AR
- Parts Used:
- WPW10683603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water inlet and valve froze and cracked
Ordered and replaced the water inlet and valve assembly from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard E from BURKE, VA
- Parts Used:
- WPW10683603
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water leak into washer drum
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GOSHEN, OH
- Parts Used:
- WPW10006384, WP90767, WP3949550
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Washer will not agitate.
After changing the cogs, inner-auger clutch assembly, retaining bolt and drive belt, the washer will still not agitate. Any suggestions??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WARMINSTER, PA
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would go into the cycle to rinse dry.
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dieu from Houston, TX
- Parts Used:
- WPW10006355
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
washer shake hole machine from begin spin about 11/2 ' h
chage out part and washer still shake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from BARRYTON, MI
- Parts Used:
- W10528947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
no spin
reviewed video of repair and repaired now washer works as it should . thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Chimacum, WA
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door latch broke
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this instruction helpful to you?
Thank you for voting!