CAW9352EW1 Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from BROOKLYN CTR, MN
- Parts Used:
- W10908289
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Non agitation
It was so simple. The staff person recommended that I just YouTube it and recommended other options. As I said it was simple,
Everything I needed was in the box.
I removed the new part from the box.
I used the equipment needed to remove the top of the Agitator's bolt.
Removed the old part, clean the inside area.
Installed the new part which took some hard pushing down onto center piece and replaced the bolt in the casing.
Placed the top back on and done.
Everything I needed was in the box.
I removed the new part from the box.
I used the equipment needed to remove the top of the Agitator's bolt.
Removed the old part, clean the inside area.
Installed the new part which took some hard pushing down onto center piece and replaced the bolt in the casing.
Placed the top back on and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norbert from PITTSBURGH, PA
- Parts Used:
- W11210459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
replace water inlet value
had to change out wiring harness was not compatible
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ROCKY FORD, CO
- Parts Used:
- W11307244
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The washer would not wash or spin.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HOUMA, LA
- Parts Used:
- W11210459
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cold water was not working
Was the video and I started everything fell into place. Thank you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from STILWELL, KS
- Parts Used:
- W11210459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
OEM water valve was allowing water to drip into the drum with no power to the valve.
Removed two 1/4” screws from the backside of control panel. Plastic putty knife slide under front of control panel to release the clips and allowing panel removal. Shut water supply off and removed both hot/cold hoses from valves. Removed the two T-20 screws which allowed the removal of the existing leaking valve assembly. Installed in reverse and it worked perfectly!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BELLEVUE, NE
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Washer acted like the lid would not latch and stopped it from cycling.
My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GEORGETOWN, KY
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer struts were wore out
Removed the old and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from TAWAS CITY, MI
- Parts Used:
- W10837741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid strike broke
Removed old one (2 screws) slid in place and screwed in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tricia from HARLEYSVILLE, PA
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer walking during spin cycle
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lebanon, VA
- Parts Used:
- W11210459
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The water inlet valve on the cold side wasn’t allowing color water flow
I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driver I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Mountain Home, AR
- Parts Used:
- W10780045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer BANGING
Believe me, I was hesitent, but after I did it, it was easy peasy, so forget the lack of confidence and dive right in.
Was this instruction helpful to you?
Thank you for voting!