CFW7400QW0 Crosley Washer - Instructions

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

Unscrew 2 screws. Replace part by screwing the 2 screws back in place. Parts received in 2days part replace less than a minute

Remove the top cover and the doorlacth and unplug the old parts as simple as that

Remove the seal ring underneath the front gasket.it's solid wire ring held together with wire spring.I used a screw driver to stretch wire ring from gasket.pulled gasket back from washer opening, near striker. removed two screws on striker lock assembly.pulled it out.removed all three wire attached to assembly.plugged in new assembly.replaced screws. reattached gasket and ring. done.

It went easy

The entire process, from diagnosing the problem, ordering the part, and instalation was fantastic! I ordered the part Friday afternoon and had it at my door Saturday afternoon. I was so relieved to read the installation posts from other customers demonstrating how common this issue is and how easy it was to fix! I simply watched the installation video that was sent with my confirmation email. It is also conveniently located on your website. I had the new part installed in less than 30 minutes AND before my husband got home! Thank you Partselect.com!

Remove the 2 screws on the rear of the top panel. Open door and remove the 2 screws holding the latch assembly. Reach down and pull up latch. Remove the 3 wire connectors. Plug wire into new latch and re-install in reverse order.

After some research online about my Frigidaire Washer, I pre-determined that the problem could likely be the lock mechanism. I ordered the part and it arrived within 3 business days. My son removed the screws from the back of the washer, slid the top off and removed the old part and replaced it with the new part. It took about 20 mins. The machine is now working properly again. The door catch that I ordered did not work with the door lock I ordered. However, the old door catch that was still in good working order does work with the new door lock and switch assembly that I purchased.

Watched your supplied video on how to repair. I did not want to break the washer door sealas described on the video. I removed the two screw on the back of washer that held the top and then slid the top off. I moved the two screws securing the switch at the exterior door. I changed the door lock and switch assembly through the top by moving the connectors one at a time from the old assembly to the new. Replaced the screws to complete. I then changed the door strike by removing the two screws and replacing the new strike. Job complete and washer works fine saving us $200.00. Thank you ever so much PartSelect.com.

took the top off removed the old one and put in the new one.Works great!!

Completed by my wife on line instruction video

Replacing the door strike is very easy. Two screws. The broken pieces stay in the door lock/switch assembly. The first time I got them out with needle nose pliers. A year later it happened again and this time I had to replace the lock/switch assembly. I followed procedure others mention here: Two screws at back of washer release the top. Slide that back. Then undo the two screws in the front of the assembly and lift it out, and replace. The important thing is that the door on the washer no longer aligns with the door lock/switch assembly, so we have to carefully (!) lift it to shut it. Do not slam. The issue with the door arises because instructions say to keep the door open so that mold does not grow in the basin. But the hinge on the door is not strong enough to support the door as it stands open when at rest over the years and it has begun to give way. This washer needs a new and stronger hinge. Meanwhile, do not slam your door. Shut it gently, lift if necessary, even on a new machine!

The front loading washer door was wobbely so I took it apart as per wife request. Hinge looked fine, bushings were fine so I started to put it back together... then the glass slipped out and to the ground. Take the time to remove the door hinge and assemble on a flat surface, then place the whole assemble back on the washer machine. Don't try to take door apart while still attached to machine. Try it you will understand and then you will be buying a new glass front.

The door assembly did not fix the problem this time, it was the control panel that had to be replaced. I have replaced the door assembly in the past, and I am glad I have a spare on hand. They do go out over time from the pressure of large batches of clothes. I am "no repair man", but having someone come out to replace it for you is a $300.00 job, easily. Read the tech info for your error code and go from there.

removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys