CW20P8ASC Crosley Washer - Instructions

Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.

Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws from snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.

I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.

Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.

Thank you PartSelect.

Andre M. Roberty

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be really smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.

this email does not include the rest of the parts i ordered. i had to replace the pump and the base panel of the washer as it was rotten. i had to open the top, remove the front panel and change out the base and install the pump. your parts and website were very helpful. thank you however this will be the last maytag i will purchase.

Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, belt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.

open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces with alcohol.install new snubber ring and assemble in reverse order.