CFW7700LR0 Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
machine would not cycle and would not drain
I read other problems, I jumped the gun and purchased the door switch, this was easy to change, but MY machine still had the same issues, however, I found that the filter was plugged, and after I cleaned this out, this fixed my issues and the machine works fine, So I now have a door switch and striker should mine go bad, Hope this helps out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gillian from New York, NY
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Strike broke
Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Atascadero, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer would drain, but not spin
Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Charlestown, MA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Error Code E43 - door lock problem - no spin
Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hyattsville, MD
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Striker
Removed two phillips screws. Removed old door striker. Replaced with new door striker. Replaced old phillips screws. Job takes less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Dyersburg, TN
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not go into spin cycle
Took off top. Removed 2 screws on Door Lock Assembly and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SCOTT from SALINE, MI
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door lock mechanism broke and washer would not run
You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kansas City, MO
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Door Strike.
Two screws out, two screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dulcenee from Bloomington, MN
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door strike just broke (who makes a plastic door strike on a machine that gets used as much as a washer?)
This was easy as pie. I unscrewed the old & put on the new. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shari from Raleigh, NC
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door strike broke while moving
very easy, just put in the 2 screws and it was fixed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ricardo from nesa, AZ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken doorlatch
Remove the top cover and the doorlacth and unplug the old parts as simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Boise, ID
- Parts Used:
- 131763302
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
plastic end of strike broken
I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darci from Norwalk, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doors tricker broke
The repair was so easy!!! It took me less than ten minutes to remove the broken piece and to install the new piece. There were 2 screws to remove to get the broken piece off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from egg harbor twp, NJ
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door striker
first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Cape Coral, FL
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door strike broke
Removed two screws and replaced the door strike.
Was this instruction helpful to you?
Thank you for voting!