CW9500W Crosley Washer - Instructions

Removed 6 screws from the metal plate on the back of the washing machine. Removed the dial from the front of the timer. You have to pop the center peice of the dial out which then frees the rest of the dial to be removed. Removed one screw from the timer back of the timer. Slid the timer out and unplugged it. Installed new timer.

I read what the others had done and thought it was the lower bearing so I originally tore it down and replaced just the lower bearing.

Unfortunately, after 2 + hours of doing that and putting it back together, it still didn't fix the problem. So I read more reviews and others claimed to use this kit and that it fixed the problem. So I ordered the kit.

BTW, Parts Select rocks!!!! They get me the part within about 2 days every time.. Great Service! Thanks guys!

Anyhow, part came in, knowing how to tear this thing down now, I was able to get to where I needed to be within about 45 minutes.

2 things that were difficult.

The first was removing the plate at the bottom of the tub. This is the aluminum plate that looks somewhat like a spoked wheel. Maytag has a tool for this. Without it, you must go at it with a small punch on one of the spokes and carefully tap the seal until it turns. You may have to try it from different angles to loosen it up but it will eventually give way..

Once you get that off, the second little piece of joy is actually removing the seal from the bottom of the tub. Here again, Maytag offers a tool to remove this. Without it, and with years of this rubberized fitting mounted in this plastic tub and corrded with water and crap... you will need to create a bearing puller.

I did so with a 2X4 board straddled across the bottom of the tub. I used an 8 inch lag bolt, drilled a hole through the 2X4 and placed the lag bolt throuigh the board and through the center of the bearing. I attached a large washer and nut to the bottom side of the bearing and then began to tighten the bolt on the other side of the board. By tightening the bolt, the board created alot of tension but not enough still to seperate it from the tub. With the tension on the bearing, I turned the tub over and tapped it with piece of wood the size of the bearing and a rubber mallet. It popped right off. The rest was just reassembly.

Don't forget to remove the sticker backing on the felt gasket to hold the gasket in place while you screw the tub back together...

The good news... Super quiet! So, about 3 hours.... (I had to come up with the idea to remove the bearing and build it) and it's all done..

Yeah.... Fun Saturday.

I had previously done a partial tear down on the machine to see if I thought I could do the repair. The dealer try's to scare you with warnings about special tools etc. Looked OK and after reading other comments on this site, I thought I would try. The only comment that I would add to what has already said is that you should have the recommended sealer or an equivalent sealer. I used weatherstrip adhesive that I had on hand. Hope that it holds up! Like it says in the directions, the seal will lift up if there is too much sealer under the lip of the seal. Just hold down the seal with a weight until the adhesive sets up and then it will stay. I've fixed cars for 30 years and this was an easy repair comparable to replacing wheel bearings.

Unplug and disconnect Power, Drain and h20 connections. Removed front panel, disconnected internal electricrical connections and capicitor from washer. Remove 11 (I think) screws connecting outer cover to base. Remove pull drain hose through the outer cover and hold the end lower that the washer to drain the excess h20. Remove the hoses from the pump and outer tub. Remove outer cover from base exposing the guts. Grab the bottom of the agitator and pull up pretty hard. Agitator will pop off, watch your head. Remove the 4 bolts attaching the Inner tub to the hub. Remove seal from top of transmission spline. You will need a 38mm deep well socket to remove the nut from the top of the transmission. I used a socket and a impact wrench to remove the nut. Remove the teflon seal that is below the nut. You will need a puller and/or grinder to remove the hub from the transmission spline. My puller broke, so I ended up using an air grinder to cut a couple of pizza slices out of the hub. Then I used an air hammer to break the slices off of the hub. Once it is cut the cast aluminum is quite brittle. Pull what remains of the hub off of the transmission spline. Remove the bolts that connect the transmission housing to the outer tub. Remove the 3 bolts from the underside of the outer tub that connect the outer tub to the upper bearing. using a set of vice grips, grab the top of the springs that connect the outer tub to the base and carefully remove them one by one.
The outer tub should slide right off. Remove the bearing from the transmission. Supplies that you will most likely need are the 3m800 sealant, when you get this you will only need a little around the bottom of the lip where the new seal attaches to the bottom of the outer tub. You will also want to get the Seal tool which will ensure that the seal that goes around the top of the transmission spline is seated properly. Assemble in reverse order but keep in mind to attach tub bolts prior to attaching the springs. Also keep in mind that both maytag and amana make a washer with the same model number LWA80AW. Check to see which one you are ordering for. The kits are different. Don't ask me how I know. Just make sure you get the correct kit the first time, it will save you a whole lot of head scratching.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

pulled washer out and unpluged it removed 6 screw removed old timer and put in new one.