CW9500W Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from Boulder, CO
- Parts Used:
- WP40053901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Washing machine was leaking
Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- H Paul from Edmonds, WA
- Parts Used:
- 27001195
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Pump was clogged by pillow packing
Dismantled the washer and cleaned out pump. Since cover-out ring was damaged, replaced it while I had the washer apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wild Rose, WI
- Parts Used:
- WP27001113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
waher would not advance in cycle
removed the timer & replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SANDY HOOK, CT
- Parts Used:
- WP22002960
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Bad tube seals and bearings
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Lenox, IL
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
drain hose had water leak
remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- 27001233
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Water Leak
Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from Tomah, WI
- Parts Used:
- 40061401, WP40045001, WP27001006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
wouldnt spin properly
removed motor removed belt replaced belt,spring,idler wheel, slid back motor in 4 bolts,plug in motor, run good on test run
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Greenville, NH
- Parts Used:
- R0131578
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer overflowed
Replaced water inlet valve with the water inlet valve kit. We ordered it on Monday morning. The part arrived the next day, Tuesday. New inlet valve was put in on Wednesday. It took less than 15 min., and my washer was working! Very impressed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Shoreline, WA
- Parts Used:
- 27001233
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Replaced Washer Pump
Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Eastpointe, MI
- Parts Used:
- R0131578
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No hot water being drawn in.
Just as everyone else explained, disconnect power and water supply, lift top of machine to get to part, disconnect old part and replace exactly with new, hook water and power supply back up and you're done. I was pleased and proud to have done it under 30 minutes (girl power!!) and that included start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Martinsville, VA
- Parts Used:
- 27001233
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
wwater pump was leaking
My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bartlett, TN
- Parts Used:
- WP22004042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
broken fin on agitator causing unbalanced wash/spin cycles
popped off fabric softener dispenser, 1/2" socket on 8" extension to remove 1 bolt. Lift agitator to remove and clean area under agitator in tub. Lower new agitator onto spindle (pretty much aligned itself) and re-inserted bolt to secure in place. Replaced softener dispenser...done. REALLY easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Waldorf, MD
- Parts Used:
- WP21001905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
softener dispenser cracked/wouldn't stay on
Cleaned the grooves well on the top of the agitator and put the new dispenser on. Easy! I suffered with the old one coming off in the spin cycle for too long. Once I located this site it was relatively easy to find the part & order it, and it arrived quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John W from Ashland, KY
- Parts Used:
- WP22004042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Blades broke from agitator
Parts where in, in a timely manner. I remover the fabric softener cup on top of agitator. User a 1/2 inch socket and a 3/8 ratchet with an 8 inch extension to remove the center nut. Popped the agitator out. Installed in reverse order, only tightening the nut slightly. The install went just like the video. Thanks much.
Was this instruction helpful to you?
Thank you for voting!