CW8203W2 (PCW8203W2 A) Crosley Washer - Instructions

Removed motor apparatus with socket, took off water pump with star srewdriver . Installed new pump. Replaced belt. Schematic diagram big help...

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

The repair was easy. It took approximately 30 minutes.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Followed video on PartsSelect website, they made it real easy.

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.

Removed front cover of machine. Removed motor/pump assembly which was held in by four (4) bolts. At the same time removed belt from transmission pulley. Removed pump assembly from motor, held in by three (3) torx fasteners. Before installing new pump installed new belt on motor assembly. While setting the motor/assembly in place threaded belt around transmission pulley. Fastened motor/pump assembly. Very easy process!

Removed the screws that held the top console which housed the timer. (5 minutes)

Laid the console over. Just rocked it forward.

Removed the 2 screws holding the timer in place.

Unplugged the wireing harness from the old timer.

Plugged the wiring harness into the new timer.

Replaced the timer and re-screwed it in place. Pulled the top console back up and re-screwed all the screws. Pushed the washer back in place and turned it on. It worked fine.

Took maybe 20 minutes.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

Just took it apart and figured out what was leaking. Ordered a piece online through Partselect. Got the piece in 2 days and put it back together. Went real smooth, saved us from buying a new washing machine. Thanks! My husband is quit the handy man too! So I thank him too!

We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.