CAH4205AWJ Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud noise
Beat on spline shaft until I gave up and trashed the washer. Bought new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Haddam, CT
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace billows on washmachine
Unscrew door hinges, front panel, soap tray, lift top to 12 oclock position,unhook strap from spring located on top of the drum,tape strap ends to drum to prevent from falling,disconnect the billows drain clamp on the bottom of the billows,remove the billows by peeling off the drum, install the new billows from the top first and tape it to the drum to prevent it from slipping off as you work your way around the drum,install the strap in its track, secure with spring(better with two people)in same location, hook up billow drain, finish doing the laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from McQueeney, TX
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser Bezel plastic cracked at screws
The repair was only 4 screws.
THE AMAZING STORY WAS I ORDERED THIS PART ON MONDAY AND RECEIVED IT ON WEDNESDAY!!!!!!
THE AMAZING STORY WAS I ORDERED THIS PART ON MONDAY AND RECEIVED IT ON WEDNESDAY!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Burleson, TX
- Parts Used:
- 22004481
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dispenser lid plastic around metal pins that insert into washer broke so it fell off everytime I opened to add soap etc
I got the part, but it did not come with the pins needed to insert into slot in washer. I had to go to Lowes and buy some pins and improvise to make them fit on both ends. It is working well....Probably saved myself $100.00 (service call etc) Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia E. from Roselle, NJ
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flanges on the bezel had broken (poor design).
Removed old screws and bezel.
replaced new bezel and screws.
The exoloded views and drawings were a great help.. Thanks for being there with views and the right parts that fit perfectly.. Love the service.. Patty O'
replaced new bezel and screws.
The exoloded views and drawings were a great help.. Thanks for being there with views and the right parts that fit perfectly.. Love the service.. Patty O'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ACCOKEEK, MD
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
reconnecting the tension spring to the wire cable took more strength than I had
Everything went smoothly enough until I reached the tension spring issue...It is definitely a two person job (that part, al least) It may be helpful to add that to the video...otherwise, the repair went well as I followed the video completely
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Harrison, NY
- Parts Used:
- WP22003834
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Hot water temperature was not heating up the water coming into the washer
Followed the online PARTS SELECT video up to the point of installing the 1/4 inch screw from the inlet valve bracket to the to the bracket housing, couldn’t get the holes to line up. I found it easier by removing the bracket from the back of the washer (2- 1/4 inch screws & holding it in my hand I was able to line up the holes & connect it. Everything went fine after that & I completed the installation. Now the hot water is heating up & working good. The online video is very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd & Shirley from CHADRON, NE
- Parts Used:
- W10181639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
washer was noisy so I replaced the bearings and put a new shaft on the tub
I looked on Utube at some videos which helped a lot all told i replaced the bearings in the outer hub which was quite a chore as the bearings came out rather hard I used a steel rod about 18 inches long and a heavy hammer to pound the old bearings out they came out hard then I put the new bearings in very carefully as I had to tap them back into place and installed the seal and put the new shaft on the tub and slid everything back into place. The instructions that came with the new seal and shaft were very helpful I bought the new bearings from local implement dealer as they were not available with the shaft and seal didn't keep track of my hours probably about 21/2 to 3 hours
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Oxnard, CA
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken plastic part in soap dispenser
Removed the broken plastic bezel and lid assembly. Removed the lid from the bezel by flexing the lid so the hinge pins would clear the mounting holes. Attached the old lid to the new bezel and reinstalled the assembly with the four existing mounting screws.
The repair was easy and for about $15.00 total the soap dispenser is back to new condition.
The repair was easy and for about $15.00 total the soap dispenser is back to new condition.
Was this instruction helpful to you?
Thank you for voting!
Dispenser Lid cracked at hinge.
I removed the dispender assembly from compartment. (Four phillips head screws.) Attached new lid to the dispenser housing. Cleaned the surface where assembly had been sitting on. Reattached the assembly unit to the washer. Looks good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Hampstead, NH
- Parts Used:
- 22002290
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser Bezel became brittle, so that screws would not hold anymore.
Unscrewed the 4 screws of the old bezel; lifted the bezel out; moved the lid from the old bezel to the new one; set bezel in place and screwed it in with the old screws. Looks and feels like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Jefferson City, MO
- Parts Used:
- 22002290, WP400021-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser Bezel broked in two places
I visited several web sites looking for repair parts for my Maytag washing machine. Your site was the easiest to navigate and provided great diagrams and pictures to ensure that I purchased the correct part. I liked the ability to track the delivery of my parts via your web site. I received my parts within a couple days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Bonham, TX
- Parts Used:
- 33002973
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
replaced two baffles
took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warwick, RI
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door hinge worn.
Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.
Was this instruction helpful to you?
Thank you for voting!