CFW4000FW0 Crosley Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- May from Abilene, KS
- Parts Used:
- 131763310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door slammed shut
door not level son slammed shut and door strike broke
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Burtonsville, MD
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Kenmore 417.41042000 Front loading washer shakes
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from MAPLE SHADE, NJ
- Parts Used:
- 134743500
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No spin
No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Littleton, CO
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would not spin or complete spin cycle
E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door lock in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door lock in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Wolcott, VT
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle to the front load washer had broken off
Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alyre from Van Buren, ME
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud humming noise from the door closure area.
First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Asheboro, NC
- Parts Used:
- 134548800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The front level screw legs are made of plastic and each time I move they break
screwed in the new legs and leveled it off again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from mount juliet, TN
- Parts Used:
- 134051003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
belt was still on washer, had developed a loose tear
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshuah from Indianapolis, IN
- Parts Used:
- 5304485917
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
One of the wash tub shock absorbers broke.
I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Vernon Hills, IL
- Parts Used:
- 131763310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door strike broke
The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Bellevue, WA
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Both shock absorbers for the tumbler had broken off
The repair itself was simple; it was the original design of the washer itself that made it time-consuming, because of the tight spaces involved. Basically, all you have to do is remove 2 plastic pins, take out the broken part, make sure you have the new part facing the right way, and put the 2 plastic pins back in. Should take 2 minutes if there are not other machine parts in the way!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Springdale, AR
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washer Door Wouldn't Lock
I watched the u-tube video and followed what he did and it was fixed. Reason it took over 15 min I had to find the correct bit for the screw. I think your web site is great thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Tolland, CT
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn't enter the spin cycle. Clothes wet at end of wash cycle.
Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Burlington, CO
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
It would not start
I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went.
Garry
Garry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Watertown, SD
- Parts Used:
- 131763310
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
a busted door striker
2 screws off and put new striker in and replaced the screws
Was this instruction helpful to you?
Thank you for voting!