CW8202W2-PCW8202W2 Crosley Washer - Instructions

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Followed video on PartsSelect website, they made it real easy.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Removed front cover of machine. Removed motor/pump assembly which was held in by four (4) bolts. At the same time removed belt from transmission pulley. Removed pump assembly from motor, held in by three (3) torx fasteners. Before installing new pump installed new belt on motor assembly. While setting the motor/assembly in place threaded belt around transmission pulley. Fastened motor/pump assembly. Very easy process!

Removed the screws that held the top console which housed the timer. (5 minutes)

Laid the console over. Just rocked it forward.

Removed the 2 screws holding the timer in place.

Unplugged the wireing harness from the old timer.

Plugged the wiring harness into the new timer.

Replaced the timer and re-screwed it in place. Pulled the top console back up and re-screwed all the screws. Pushed the washer back in place and turned it on. It worked fine.

Took maybe 20 minutes.

The repair was easy. It took approximately 30 minutes.

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

Just took it apart and figured out what was leaking. Ordered a piece online through Partselect. Got the piece in 2 days and put it back together. Went real smooth, saved us from buying a new washing machine. Thanks! My husband is quit the handy man too! So I thank him too!

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.

Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.

The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!