LW6143LM-PLW6143LM Amana Washer - Instructions

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

Removed motor apparatus with socket, took off water pump with star srewdriver . Installed new pump. Replaced belt. Schematic diagram big help...

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

First I removed 2 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new value and put it back in place. I then put the screws back in place.

This was very easy and it solved my problem

Thanks a lot

Just follow the video. The hardest part is getting the top to disengage from the clips.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

1. Removed the hot and cold water hoses. 2. Undid one screw holding on the solenoid mounting plate. 3. Pushed the plate in at the top to unlatch the plate at the bottom. 4. Pulled the plate out and undid the output hose. 5. Replaced the solenoid assembly held on by two screws. 6. Replaced it all in the revers order.

Removed the cover on the washer controls. Loosed the knob and popped it off. Then disconnected the plug and replaced with the new part. Put th ekonb back on and closed it all up. It was pretty easy. Took longer to reomove all the screws than it did to remove and replace the part.

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

Installed the new part. Worked great!

Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.