AWM190W Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from East Berlin, PA
- Parts Used:
- WP28808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washing machine was making a banging noise
Turned off water & unpluged ac power. Removed 2 screws on front panel. Removed panel. Found peices of V belt. Removed 4 screws from electric motor which allowed the belt to come out. Ordered new belt on line. Received the item in one day. Reversed the above sequence above. Now the washer is running as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from O'Fallon, MO
- Parts Used:
- WP34963
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No Hot water
I purchsaed a new water valve and it was very easy to install. I hate to do thos kind of repair but it went very smooth. Took maybe a half hour, and now it works like new.
Was this instruction helpful to you?
Thank you for voting!
Leaking water
detached 2 inlet/ oulet hose/ hose clamps.removed the 4 motor/ pump base screws, tilted motor/ pump assembly and pulled from washer. Removed the 3 pump housing screws, removed pump/ old drive belt. installed new drive belt, pump, reattached pump screws, motor/ pump base screws, reattached hose/ hose clamp. Rreplacement of parts took approxmiatley 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pflugerville, TX
- Parts Used:
- WP34963
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The old water inlet valve was stripped.
Removed the back plate. Disconnected the inside water hose. Unplugged the electrical contacts. Pulled out the old valve, connected the water hoses to the valve, plugged in the electrical contacts, reconnected the inside water hose, and put the plate back on the washer. The hardest part was putting the plate back on the washer. This entire repair would have been exceptionally easy except that I had to sit on top of the washer and hang upside down to do the repair due to the extremely small space the washer was in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Lawrence, KS
- Parts Used:
- WP34963
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water pumped in very slowly.
Unplugged washer, turned water valves off, disconnected water lines from washer with adjustable channel-lock wrench. Water inlet valve was mounted on its own plate that needed removed using a screw driver. Disconnected the electric sensors and disconnected the outlet hose. Valve had to be taken off the mounting plate with a nutdriver. Replaced valve and reconnected everything. Water pumped in 10 times faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- millie from hot springs village, AR
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
pump leaking water
remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor
Was this instruction helpful to you?
Thank you for voting!