NTW4516FW0 Amana Washer - Instructions

I ordered the part and watched the installation video. It would have helped if I had watched the video all the way through at least once. Instead I paused and restarted it as I did the repair. As a result I had a hard time putting the agitator back together. Otherwise it was a fairly easy repair and my 20-year-old washer works great again!

I figured out through the process of elimination that the problem was the rubber plunger that the solenoid opens and closes. I couldn’t fix just the plunger so I replaced the whole water inlet valve and the cold water worked perfectly after that. Even though it was a little tough to diagnose the problem it was very easy to replace the part once I found out what it was that was wrong.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Part fixed it perfectly.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

I popped the cap off of the agitator. I could see the grabbers weren't grabbing the side of the agitator. I thought I could take a shot at fixing it since I was ready to give up. Happened upon this site. With the model number, I was very easily able to find the parts I needed. Ordered them up. Took one bolt out of the assembly and the whole agitator came off. I popped in the new parts as the diagram was very easy to follow, resecured the bolt, and all was good. I saved a ton of money off replacement or even calling a service tech. Your site made this very easy with the detailed diagrams. Didn't order anything I didn't need. Only cost $11 to fix it and made me feel like Mr. Fixit. I will definitely use your site as my first, best choice for any problems I have in the future.

The process to replace the nylon pieces was to remove the protective cap, (which snaps in place),agitator (which is held in place with a nut) you will need a socket with an extention to reach the nut, and worn parts. replace the agitator repair kit, agitator and protective cap and your washer works as good as new. This is a very simple repair job, even a 10 yr old could do this

took out old agitator and installed new one, machine now runs like new. couldn't be happier.

Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Replaced agitator sprage kit. Simple instructions simple repair