Models > NTW5100TQ1 > Instructions

NTW5100TQ1 Amana Washer - Instructions

Jump to:

All Instructions for the NTW5100TQ1
121 - 135 of 682
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dale from DOTHAN, AL
Parts Used:
8316845
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Washer tub goes out of balance in spin cycle.
Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Floyds Knobs, IN
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
washer tub did,nt spin
leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juana from MANOR, TX
Parts Used:
WP3949550, WP358237
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Washer not spinning properly.
Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from BLUE POINT, NY
Parts Used:
63580
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Machine delivered without fabric softener dispenser.
Removed the cover where the dispenser would have been installed and snapped the new one in. 5 minutes. When useing the dispenser after adding softener make sure to fill the dispenser with water to dilute and prevent staining.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from ATLANTA, GA
Parts Used:
WP8318084
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bad lid sensor
Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
luis from ocoee, AL
Parts Used:
WP8318084
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Washer Would Fill With Water But Not Turn On
Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda Dianne from Poteau, OK
Parts Used:
WP358237
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Socket set
could not get the bottom agitator to release, so finally just left it in place, first bolt I had did not fit right so ordered one directly from your store also had to wait dor my tools to get in
I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Emmett from WEATHERFORD, TX
Parts Used:
40922
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Socket set
Needed to extend drain hose to reach drain
Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from North Charleston, SC
Parts Used:
285785
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Socket set
Spin cycle worked very poorly
1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from SIOUX FALLS, SD
Parts Used:
63580
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Fabric Softner Dispenser severly pluged
Watched the video on this site on removal and installment Done in less than 5 minutes including cleaning where the dispenser is located
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jonathan from Glen Cove, NY
Parts Used:
285753A
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
washer drum not turning
Turn off the power,remove the washer cabinet top and side panels. unsnap the water pump clips, unscrew and unclip the motor mounting clips.Remove the old drive coupling and triangular drive shaft adaptors.Clean area and install the three new parts, reattach the motor and pump, close the cabinet,turn the power back on and test.Done! The only hard part is working down on the floor and you need a good flashlight.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Mountain Top, PA
Parts Used:
285753A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Coupling broke
After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Apple Valley, MN
Parts Used:
285753A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
basket would not spin during spin cycle
Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Terre Haute, IN
Parts Used:
285753A, WP8318084
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
No spin or agitation
I removed four srews holding the control panel and laid it to the side, then removed a screw holding the ground on and disconnected the electrical connection. The lid needs to be open to remove the switch. Just remove the switch and reverse sequence. To replace the coupling , I laid over the washer and removed two screws holding the straps connecting the motor to the transmission. After seperating, I pulled off old couplings and reinstalled the new ones on both the motor and transmission. I had to tap couplings on. Then reversed the installation and set backup and tried it out. It worked great.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Carmel, IN
Parts Used:
WP8318084
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The machine would cycle properly all the time.
I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the NTW5100TQ1
121 - 135 of 682