Models > NFW7600XW00 > Instructions

NFW7600XW00 Amana Washer - Instructions

Jump to:

All Instructions for the NFW7600XW00
121 - 135 of 160
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
WILLIAM from SAINT CHARLES, IL
Parts Used:
W10822553
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
washer jumping when spinning
open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSE from WOODBURN, OR
Parts Used:
280187
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
washer weren't drain
Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gene from Killeen, TX
Parts Used:
280187, WP8182210
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Impeller broke on water pump
Replaced pump assembly
Was this instruction helpful to you?
Thank you for voting!
Customer:
Monica from Las Cruces,, NM
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Not draining, code FO2
Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from North Pole, AK
Parts Used:
WP8182210, WP8182119
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bellow had a large hole in it, and was letting water drain out all over the floor.
It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Troy, MI
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Water smells bad if washer sits for a few days.
I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.
Was this instruction helpful to you?
Thank you for voting!
Customer:
david from bozeman, MT
Parts Used:
280187, WPW10426377
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Squealing towards end of cycle during high speed spin
Made a bad call after googling "bearing squeal for HE 4t" and replaced the bearings and seal on the drum.... Turns out my squeal was coming from the drain pump, didn't realize until after a major tear down and replacement of bearings and seal. Managed to break one of the electrical connectors on the heating element on that repair as well... Compared to the bearing replacement the drain pump was super simple. Lots of good instructions above, the only thing I would add is that if you put a little pressure on the hose clamps and spin them to an easier position to see and get pliers on, they will be much less of a headache. Vice grips were the best tool for getting them released and re-installed. The heating element was pretty easy, loosen the center nut to the end of the threads but don't remove. Use a flat screwdrive to gently pry the unit out. Use a little dish washing soap to lube up the rubber plug on the new one before installing and it slides right in.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Billie from Dixie, WV
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Wasn't draining
Washed three loads and it was ok but then it stopped draining again. I don't know what to do.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tracey from Salem, OR
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Drain pump wasnt working
Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Great Mills, MD
Parts Used:
WPW10289387
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Sediment clogging valve - E01F08 error code
Shut off water and disconnect hot and cold hoses. Use nut driver to remove three screws at back/top of washer. Slide top of washer back and up to remove. Use pliers to loosen band clamp on rubber hose and pull away from valve assembly. With fingers, disconnect wiring from hot and cold solenoids. Use allen wrench to remove valve assembly from frame of washer. Use reverse order to install replacement valve, although you can leave the top off the washer until you've checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Katherine from Ridge, NY
Parts Used:
280187
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
My washing machine was not draining
I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
Customer:
turbo trucking from mio, MI
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Won't spin
Replaced water pump
Was this instruction helpful to you?
Thank you for voting!
Customer:
donald from Stanwood, WA
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
torn bellow
repair was a cake-walk with the video there to help.Thanx
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Anderson, SC
Parts Used:
WPW10388414
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
drive belt slipping
Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ann from Algonquin, IL
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The washing machine wouldn't drain
I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the NFW7600XW00
121 - 135 of 160