Models > NFW7200TW11 > Instructions

NFW7200TW11 Amana Washer - Instructions

Jump to:

All Instructions for the NFW7200TW11
46 - 60 of 98
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
LISA from PRINCETON, WV
Parts Used:
WP34001324
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
OE error. All i read indicated the need for new sensor, but it did not correct the problem.
My husband simply removed the old sensor and put the new one in. It was not difficult.
8 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Boynton Beach, FL
Parts Used:
350930
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
23 of 76 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from Manhattan, KS
Parts Used:
WP34001432
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Seal torn on washer
Removed the front face of washer (broke the plastic pieces on face-no big deal). Had to remove the front housing piece to remove the inner clamp then remove seal. Aligned the new seal up and worked backwards making sure all screws were tightened down. Not super hard, but breaking the plastic pieces wasn't fun.
Was this instruction helpful to you?
Thank you for voting!
Customer:
becky from Lehi, UT
Parts Used:
WP34001260
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Problem with the door latch
It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jennifer from Staunton, VA
Parts Used:
WP8182634
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
The latch was broken so that the front door wouldn't close.
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary Ellen from Waconia, MN
Parts Used:
WP34001340
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Was not draining
Purchased the pump from PartSelect after reading other reviews and let me tell you....it works great now. Way cheaper than hiring a repairman.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Timothy from Bismarck, ND
Parts Used:
WP34001340
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
I was getting an "nd" error code with every wash cycle.
I removed the back service panel and checked the drain hose for any debris and checked the connection from the tub basin to the drain pump. I then check the drain pump and noticed the impeller blades were a bit worn. After the new drain pump arrived, I did have to swap the old intake housing with the new one in order for the whole thing to mount to the shock-absorbing mounting plate. Reconnected both hoses and the electrical connection and everything ran great!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Andrea from Rochester, MN
Parts Used:
WP34001260
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
installing new door latch
first of all, I am not at all handy, so that fact that I could do this at all is pretty amazing. I watched the video and it was very good. At first all went smoothly...I got the top off, the control panel off and the detergent drawer out. Then I ran into problems, three of the six screws holding on the front panel wouldn't come out. I sprayed Liquid Wrench on, waited for a while, still wouldn't come off, then I tapped them with a hammer, still wouldn't unscrew. But I was able to access the door latch from the top rather than the side...a little tight and awkward, some swearing was required, but it worked. Machine now working like a charm, yay!
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Manchester, NH
Parts Used:
WP34001303, WP34001292
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Wrench set
shakining and moving
Installed dampners with a little trouble because of location on machine. But turned out not to be the problem. Machine still shakes and move. Looking for for another reason for shaking. Replacing dampners would be a "do it yourself project" for most people.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marybeth from Warwick, RI
Parts Used:
WP8182634
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Washer flashed error code DL (door lock) and wouldn't start.
We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from New Milford, CT
Parts Used:
WP34001340
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Error code nD not draining
I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Byron from Bellaire, TX
Parts Used:
34001411
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Washer shaking on spin and spin speed low.
I simply followed manufacturers direction from the service manual that I had purchased. I removed the cover from the back of the washer, removed the old belt and put the new belt on. The old belt was certainly stretched and putting the new belt on simply required that I walk the new belt on to the pulley and then adjust the belt to the center of the pully. The end result was a washer that now spins as it did when new.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dee Earl from Pocatello, ID
Parts Used:
WP8182634
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Door latch/lock assembly needed replacement
The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dora from West palm beach, FL
Parts Used:
WP34001340
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
impeller destroyed, over worked the pump motor and burned it out
this is a front load washer, removed a small access plate from the back of the washer, removed the old pump and install the new one
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from Cincinnati, OH
Parts Used:
WP34001260
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door lever was broken
Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the NFW7200TW11
46 - 60 of 98