ALW210RMW-PALW210RMW Amana Washer - Instructions

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

I used my three jaw slide hammer to remove the pump from the motor. How are other people getting it off? Pump made alot of rubbing noise after installation. I tried pushing it on farther and also prying it back off a little with no luck. It's really cheap looking and I was scared of breaking it. The thing wasn't leaking so I called it good....

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

Replacing the spin belt is like the others have said, but I'll add a couple of cautions. Don't try to separate the driven pulley on the water pump from the pump shaft. Instead, separate the water pump from the driven pulley. And, make sure you know the routing of the belt for reassembly, because it has to go between the correct legs that support the water pump. Get it wrong and you'll have to start all over. I pulled the machine away from the wall by about 18" and put a block of wood under the front of the machine to raise only the front to 9" or 10" off the floor which made it easier to do the work. Try and take a digital photo of the belt routing from a couple of angles before beginning. Don't forget to route the belt around the tensioner pulley.

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Basically you have to remove the drive motor and pump (in that order). This allows you to get the belt around the drive motor pully wheel. It took me a few tries to get the belt routed right. I assume that if you know what you are doing you can complete this in under an hour. It took me about 4 hours, though - cause I didn't know what I was doing at first. Hehe.

Hope this helps.

I first ordered the parts and to my dismay, I ordered the wrong belt for the spin belt. I called customer service in which received an Return Merchandise Number and ordered the correct belt. PartSelect was prompt on sending the correct out by FedEx, thank you for an excellent experience.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!