LWC07AW (PLWC07AW) Amana Washer - Instructions

First I unscrewed the bottom of the front panel.
Then I realized the front panel pulls off from the top.
(manuals are helpful only if read!) I took the tub hose off at the tub and used my wet vac to remove all the excess water. (no towel needed) Using the appropriate size torx head bit, an extension and a small socket wrench to undo the screws holding the pump. I had to push and pull the bottom of the tub slightly to get proper room for the small socket wrench. pull the pump down and off. take the hoses off and place them on the new pump. reverse the process. tighten the clamps and replace the front cover.

Pulled the old knob off and replaced with new knob
PartSelect sent me the exact part you can't tell the difference.

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

I removed the front lower panel. I disconnected the springs holding the motor to the chassis. I removed the belt off the pump pulley. Pay attention to the way the belt runs from the pulley and through the pump. This will aid in placing the pump back on so the belt runs correctly. Disconnected the wires, removed the capacitor bracket so I could take the motor/pump unit out after I removed the 4 bolts holding the motor/pump unit. Removed the 3 torx screws holding the pump to the motor. Matched the new pump to the old to make sure the new one was correct.

Installed in reverse order.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

replaced belt that was wore out. decided to replace pump while I had washer apart.

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

I read instructions on how to change the pump. I unplugged the washer and then I took off the front panel.I removed the hose clamps and removed the two hoses from the pump.Then I removed the two front springs that hold the drum in place. Be careful because these springs are under tension. I removed the 4 bolts that held the motor to the tub. I unplugged the wires leading to the motor. I removed the motor. I turned the motor upside down and removed the pump and belt. I ordered a belt along with the pump because it was worn. It is best to note how the belt is installed. I took a picture before removing the pump from the motor for future reference if needed. Installation of the new pump and belt was not difficult. I worked the belt around the drum pulley and made sure it turned freely. After completing installation I ran the washer through a short cycle to check for leaks before installing the front cover.

took front of washer off;took sheetmetal bolts out of the base and lifted sheetmetal surround. disconnected filler hose and water level tube, took sheet metal jacket completely off machine and disconnected 4 of the 6 drum tensioner springs. Tilted drum back at 45 degree angle and removed pump unit. Changed tensioner pulley and drive belt. Reassembled works great! Thank You. We got the machine for free from our my inlaws because it made a funny noise. We ran it for a year with the funny noise and it worked great til one evening it just got tired and quite. We were going to go buy a new washer the next day but decided to go online first and check about parts; Glad we did;only cost $80 to fix! Thanks again!

a nail from my pocket fell out and was in one of the holes in the in the tub and bound up the tub.when it wold try to spin.ordered the belt and had to order a pump also it melted the bearing in it