ALW480DAC Amana Washer - Instructions

Followed instructions that came with parts. Still making a noise not as loud as before, must be transmission bearing.

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

replaced belt that was wore out. decided to replace pump while I had washer apart.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

With the right tools this job, should not be that complicated, to me the hardest part was finding the right tools, 1/4 inch small rachet ( the smallest the better,) with a 2 inch extension and a Torx head socket, also known as a 6 lobe,(T25 thats the # that is on the socket) also you need a flat head screw driver,or a 1/4 socket to take the cover off.. and of course the right belt, you might also need a flash light, watch out for spiders, specially black widows, i found a few, First you take the cover off, it should be the easiest part, then, put the rachet,( the smallest the better) with the 2 inch extension and the socket, to take out the water pump, it should be white, it should be only three screws, take your time, when taking out the screws hold them so they don't fall, in to the whasher, it happened to me and it took me a long time to find one of the screws, once you take the 3 screws move the water pump aside it should just drop down from the shaft that drives it, it is not necessary to take the hoses off the pump, put the new belt in place, make sure place it trough the tensioner, there is a guide in the AMANA web site when if you are not so sure, on how the belt goes, once you place the belt, put the water pump back, put the three screws back, put the cover back, run the machine trough a new cycle, Reason why is because i try to run it trough the spin cycle only after i put it together and the belt wouldn't spin, only the motor,Don't forget to unplug the power from the wall before staring all this, I hope this was of some help to you,

The instructions included were very good. The biggest problem I ran into was removing the inner tub from off the hub. Using PB Blaster was the trick there, but still took some effort to finally pry it lose without damage. The hub screwed right off after and removing the Triple Lip Seal was easy enough with screw drivers. Cleaned things up and replaced it by gently tapping around it to seat it evenly. Reassembly also went well, but I DO HAVE a story. Being as careful as I thought I could be, I still somehow broke the outer tub. I read about others experience, buying and using JB Weld WaterWeld to fix it. Now the washer is so quiet again that you have to look into the drain tub to see if it is spinning. AWESOME

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

a nail from my pocket fell out and was in one of the holes in the in the tub and bound up the tub.when it wold try to spin.ordered the belt and had to order a pump also it melted the bearing in it

Fixed the problem easy to do just take your time putting in bearing in plastic tub

After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.

thought wire between hot and cold valve was to short but after many phone calls found out valve could be ajusted by prying carefully up clips and moving valve closer not in directions

Laid washer back on a appliance dolly, removed the front cover, checked to see if the hose was touching the motor mount (it was). Removed the drain hose from the pump and standoffs, removed the hose and disk from the back of the washer that holds the hose. Replaced the hose on the pump, turn the standoff to move the hose farther from the motor mount, and install it in the disk. May be easier to measure the hose and do the disk first as it is not easy to get the hose bent when it is installed first on the pump.