ALW540RAC Amana Washer - Instructions

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts

checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.

Followed video on PartsSelect website, they made it real easy.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

I had previously done a partial tear down on the machine to see if I thought I could do the repair. The dealer try's to scare you with warnings about special tools etc. Looked OK and after reading other comments on this site, I thought I would try. The only comment that I would add to what has already said is that you should have the recommended sealer or an equivalent sealer. I used weatherstrip adhesive that I had on hand. Hope that it holds up! Like it says in the directions, the seal will lift up if there is too much sealer under the lip of the seal. Just hold down the seal with a weight until the adhesive sets up and then it will stay. I've fixed cars for 30 years and this was an easy repair comparable to replacing wheel bearings.

I used my three jaw slide hammer to remove the pump from the motor. How are other people getting it off? Pump made alot of rubbing noise after installation. I tried pushing it on farther and also prying it back off a little with no luck. It's really cheap looking and I was scared of breaking it. The thing wasn't leaking so I called it good....

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.